Chicken EST (ChEST) clones

Please note that the clone(s) being sent have tested negative in our phage contamination assay. However these clones should still be handled with care as no phage assay can be guaranteed to be 100% accurate.

What to do with your clones when you receive them

The clones have been streaked onto LB agar containing 50 µg/ml carbenicillin. Please store them at 4°C (not in a freezer).

As soon as possible, re-streak the clones onto the same medium and incubate overnight at 37°C to obtain single colonies.

A selection of at least 10 single colonies should be picked and grown in LB broth containing carbenicillin + 8% glycerol for subsequent freezing at -70°C. These frozen stocks can then be re-grown for plasmid isolation and purification.

Streaking out for single colonies is essential in case of contamination or cross-contamination, or if modifications of the original clone have taken place as the library has been replicated. If there is a problem, the more single colonies you streak out, the more likely it is that you can retrieve the original construct. You can also isolate the original clone from a contaminated sample by following this procedure.


Vector information

pcDNA3.1 [Invitrogen - ]

NB: This vector has been used only for clones from plate 1 of the library (ChEST1a1 - ChEST1p24)
Chicken EST clones 1


Vector information: Insert flanking sequence pcDNA3.1 vector


Vector information

-Vector name pcDNA3.1
-Cloning sites and orientation of library inserts (5'/3') NotI/EcoRI
- Promoter 5' of the inserts T7
- Sequencing primer 5' of the inserts T7
- Promoter 3' of the inserts pcDNA3.1BGHreverse
- Sequencing primer 3' of the inserts pcDNA3.1BGHreverse

pBluescript II KS+ [Agilent Technologies-]

NB: This vector has been used for all clones from plate 2 onwards (ChEST2a1 - ChEST1038p24)


Chicken EST clones 2


Vector information: Insert flanking sequence  pBlueScript II KS+ vector

Vector information

-Vector name pBlueScript II KS+ (Stratagene)
-Cloning sites and orientation of library inserts (5'/3') NotI/EcoRI
- Promoter 5' of the inserts T7
- Sequencing primer 5' of the inserts M13F
- Promoter 3' of the inserts T3
- Sequencing primer 3' of the inserts M13R

pBluescript II KS(+/-) Multiple Cloning Site Region
(sequence shown 598-826)


Chicken EST clones 3

Recommended methods for isolation and purification of DNA

Plasmid DNA mini-prep preparation

Any standard mini-prep method is suitable. Below is the method used in-house at Source BioScience LifeSciences.

a) Streak out plasmid onto LB + ampicillin Incubate overnight at 37°C

b) Dispense 5ml LB medium into a 50ml sterile tube. Add appropriate antibiotic. Inoculate with a single colony and incubate overnight in shaking incubator 37ºC /170 rpm.

c) [If a glycerol stock is required, transfer aliquot of 140µl to a 1.5ml microtube. Add 40µl 80 % glycerol. Mix and freeze.]

d) Take 2ml of the plasmid broth, transfer to a 2ml microtube, and centrifuge 15 min 3000 rpm.

e) Pour off supernatant and discard. Re-suspend pellet in 200µl GTE.
Add 5µl RNAase A stock (10mg/ml). Incubate 10 min. room temperature.

f) Lysis: Add 400µl 0.2M NaOH/1% SDS (freshly made). Mix by inversion. Place on ice for 5 min.

g) Add 300µl 3M K Ac. Invert to mix. Place on ice for 10 min

h) Centrifuge 10 min at 13000 rpm in microfuge. Decant supernatant into a 1.5ml microtube
containing 1ml cold ethanol, vortex briefly and leave to stand for 30 min. on ice.

i) Centrifuge 10 min. at 13000 rpm in microfuge. Remove ethanol carefully (preferably by suction technique).

j) Add 200µl cold 70% ethanol, vortex briefly, centrifuge 10 min. at 13000 rpm in microfuge, remove ethanol carefully (as above).

k) Air dry pellet. Add 50µl TE and leave to re-suspend overnight at 4°C.



10 ml GTE:
0.5 ml 20% glucose
0.25 ml 1M Tris/HCl pH 7.5
0.2 ml 0.5M EDTA pH 8.0.
9.05 ml sterile distilled water

Lysis Buffer:
100 ml 0.2M NaOH/1% SDS = 0.8 g NaOH
5ml 20% SDS
95ml sterile distilled water.


PEG purification of plasmid DNA (strongly recommended before sequencing)

a) Add an equal volume of 20% PEG solution in 2.5M NaCl. Incubate at room temperature for 5-10 min.
Spin for 10-15 min. at 13,000 rpm.

b) Remove supernatant and rinse pellet with 70% ethanol. Dry the pellet. Resuspend in 20µl sterile
distilled water.

c) Remove 5µl and add to 2µl loading buffer. Run out with appropriate DNA marker on a 1.5% TBE
agarose gel to check that DNA recovery is good.

d) The DNA is now ready for sequencing.


General PCR purification method

Clones can be amplified by PCR using the appropriate flanking primers. PCR products should then be purified using spin columns or the sAP/exo1 (shrimp alkaline phosphatase/exonuclease1) method prior to sequencing.


Werle. E, Schneider. C, Renner. M, Volker.M and Fiehn. W. (1994) Convenient single-step, one tube purification of PCR products for direct sequencing. Nucl. Acids Res. 22: 4354-4355.


Hanke. M and Wink. M. (1994) Direct DNA sequencing of PCR-amplified vector inserts following enzymatic degradation of primer and dNTPs. BioTechniques 17: 858-860.